There’s no single best simulation software. The right tool depends on what you’re simulating. For electronics and embedded systems, these are good defaults:
- Analog and power circuits: LTspice (free) or ngspice (free and open source, built into KiCad)
- Firmware running on a virtual microcontroller with a simulated circuit: Proteus VSM (commercial) or, for hobby boards, Wokwi
- Arduino basics for beginners: Tinkercad Circuits or Wokwi in a browser
- Firmware testing with no hardware at all: Renode or QEMU
- Control systems and system-level models: MATLAB/Simulink (commercial) or open alternatives such as OpenModelica
Outside electronics, the usual leaders differ by field: ANSYS and COMSOL for structural, thermal and multiphysics work, AnyLogic and Simio for business processes, Gazebo and similar tools for robotics. The rest of this article focuses on electronics and embedded systems.
Quick picks by task
| What you want to simulate | Good choices | Cost |
|---|---|---|
| Op-amps, filters, power supplies, transients | LTspice, ngspice, PSpice, TINA-TI, Multisim | LTspice, ngspice, TINA-TI free; PSpice and Multisim commercial (with free/limited editions) |
| Quick “how does this circuit behave?” experiments | Falstad circuit simulator, EveryCircuit, CircuitLab | Free to low-cost |
| Schematic + PCB + SPICE in one free tool | KiCad (uses ngspice) | Free, open source |
| Firmware on a virtual MCU plus a circuit | Proteus VSM, SimulIDE, Wokwi, Tinkercad Circuits | Proteus commercial; others free or freemium |
| Firmware with no hardware, in CI | Renode, QEMU, vendor IDE simulators | Free (Renode, QEMU) |
| Control loops, motors, signal processing | MATLAB/Simulink, Simscape, OpenModelica, Xcos | Simulink commercial; others free |
Circuit simulation (SPICE)
Most circuit simulators are built on SPICE, a simulation engine first developed at UC Berkeley in the 1970s. You draw a schematic (or write a netlist), assign component models, and run analyses such as DC operating point, AC frequency sweeps and transient (time-domain) simulations.
LTspice
LTspice, from Analog Devices, is one of the most widely used SPICE simulators. People like it for:
- Fast simulation of switching power supplies, which some general-purpose simulators handle slowly
- A large library of Analog Devices (including former Linear Technology) parts and demo circuits
- A built-in schematic editor and waveform viewer
- Wide use in tutorials, application notes and forums, so help is easy to find
It runs on Windows, and a macOS version is also available.
ngspice (and KiCad)
ngspice is an open-source SPICE simulator that’s actively developed. It’s the simulation engine inside KiCad, and it’s used by tools such as Qucs-S. It’s notable for:
- Being open source and running on Windows, macOS and Linux
- Mixed-signal simulation through its XSPICE extensions
- Scripting and batch runs, which suit automated design checks
- Support for modern compact device models
Is ngspice better than LTspice?
Neither is better for everyone:
- Choose LTspice if you want a polished standalone simulator, you mostly use Analog Devices parts, or you simulate switching regulators a lot.
- Choose ngspice if you design PCBs in KiCad and want simulation in the same tool, need Linux support or open-source licensing, or want to script simulations.
Both read standard SPICE netlists. Vendor models sometimes use syntax specific to PSpice or LTspice, though. ngspice has compatibility modes for these, but you may still need to adjust some models.
Is LTspice completely free?
LTspice is free to download and use, with no license fee and, unlike some “free” simulators, no artificial limit on circuit size. It’s not open source, though. It’s proprietary software that Analog Devices distributes at no cost. Check the current license terms on Analog Devices’ site if you plan to redistribute it or bundle it with something.
Other circuit simulators
- PSpice (Cadence): common in industry and education. A free edition with limits is available, and TI offers a free “PSpice for TI” version with its own parts.
- TINA-TI: a free simulator from Texas Instruments, oriented toward TI parts.
- Multisim (NI): popular in teaching, with strong virtual instruments. There’s also a browser-based version.
- Qucs-S: an open-source front end that can use ngspice and other engines.
- Falstad: a browser-based simulator that shows current flow in an animation. It’s great for learning, not for precise analysis.
Microcontroller and circuit co-simulation
These tools run your compiled firmware on a model of the microcontroller, wired to simulated components such as LEDs, LCDs, sensors, motors and serial terminals.
- Proteus VSM (Labcenter Electronics): the best-known commercial option, with models for many PIC, AVR (including Arduino boards), 8051 and selected Arm microcontrollers, plus virtual instruments and a PCB design tool. It’s Windows-only. See what Proteus software is for a fuller look.
- Wokwi: browser-based and also available as a VS Code extension. It supports Arduino boards, the ESP32 family, Raspberry Pi Pico and some STM32 parts, and you can share a project with a single link.
- SimulIDE: free and open source, with AVR, PIC and Arduino support. It’s lightweight and good for teaching.
- Tinkercad Circuits: free in the browser, built around the Arduino Uno, with block-based or text coding. It’s very beginner-friendly.
These are excellent for learning, teaching and checking logic. Peripheral models are approximations, however, and timing-sensitive behavior may not match real silicon exactly.
Firmware emulation without hardware
If the goal is to run and test firmware automatically, for example on every commit, emulators fit better than circuit tools:
- Renode (Antmicro, open source): emulates complete boards, including CPU, peripherals and even networks of several devices. It’s scriptable and commonly used in CI for Zephyr and other RTOS projects.
- QEMU: emulates many processor architectures. It’s widely used for embedded Linux on Arm and RISC-V, and it supports a limited set of Cortex-M boards.
- Vendor simulators in Keil µVision and MPLAB X: instruction-level simulation for supported chips, useful for algorithm and timing checks.
For more on how these tools fit alongside IDEs and debuggers, see embedded development tools: IDEs, toolchains and simulators.
System-level and control modeling
When you’re designing a control algorithm, such as a motor speed loop, a battery charger or a digital filter, it’s often easier to model the whole system mathematically before writing firmware:
- MATLAB/Simulink (MathWorks): the industry standard for model-based design, with add-ons for physical modeling (Simscape) and automatic C code generation for embedded targets.
- OpenModelica: an open-source environment for the Modelica modeling language.
- Scilab/Xcos: an open-source block-diagram simulation tool.
- Python (NumPy, SciPy, python-control): flexible for quick analysis if you’re comfortable writing code.
Simulation outside electronics
If you came here from a different field, these are the usual starting points:
- Structural, thermal, fluid and electromagnetic analysis: ANSYS, COMSOL Multiphysics, Abaqus, SimScale
- Business, logistics and manufacturing processes: AnyLogic, Simio, Simul8
- Robotics: Gazebo, Webots, MuJoCo, NVIDIA Isaac Sim
How to choose
Ask these questions in order:
- What do you need to learn from the simulation? A voltage waveform calls for SPICE. “Does my firmware respond correctly to a button and sensor?” calls for MCU co-simulation. “Does my firmware still pass tests after this change?” calls for an emulator in CI.
- Which parts are you using? Check that the simulator has models for your exact microcontroller or ICs. Vendor-provided models often decide the tool.
- What’s your budget and platform? LTspice, ngspice, KiCad, Wokwi (free tier), SimulIDE and Renode cost nothing. Proteus, Multisim, PSpice (full) and Simulink are paid, and some are Windows-only.
- Does it fit your workflow? If you lay out PCBs in KiCad, its built-in ngspice saves a step. If you work in VS Code, Wokwi’s extension is convenient. If you need automation, pick something scriptable.
Limits of simulation
Simulation is only as good as its models:
- Component models may leave out parasitics, temperature effects and tolerance spread unless you add them.
- Microcontroller models may not reproduce every peripheral quirk, silicon erratum or exact timing.
- Real boards add noise, ground bounce, EMI and layout effects that most simulations don’t include.
Use simulation to catch mistakes early and explore designs quickly, then confirm on real hardware with an oscilloscope, a logic analyzer and a debugger. When firmware misbehaves on the real board, debugging microcontrollers with JTAG, SWD and GDB is the next step.