What makes a strong senior design project
There’s no single “best” topic for a final-year project. A strong senior design project usually has these qualities, whatever the subject:
- A real problem with a user. Someone, even a hypothetical but well-defined someone, would want the thing you’re building.
- Measurable requirements. “Measures heart rate” is vague. “Measures heart rate within ±5 BPM of a reference device at rest” is something you can test and defend.
- A genuine engineering trade-off. Cost against accuracy, battery life against update rate, latency against power. Judges and advisors want to see you made decisions, not just assembled modules.
- Enough depth for every team member. Each person needs a substantial piece they own and can explain.
- Feasibility. It has to be buildable with your budget, skills and timeline, usually one or two semesters.
Projects that combine custom hardware (at least one PCB of your own design) with meaningful firmware or software tend to show the breadth that electrical and computer engineering programs are looking for. Check your own program’s rubric, though, because expectations vary between schools.
Project ideas by area
Each idea below lists what you’d build, where the core difficulty lies and what you could measure to prove it works. Treat them as starting points to adapt, not finished specifications.
Embedded and IoT systems
Low-power environmental sensor network. Several battery-powered nodes report temperature, humidity or air quality to a gateway over LoRa, BLE or Zigbee. Challenge: power budgeting, radio reliability, gateway software. Measure: battery life (measured and projected), packet delivery rate against distance.
Smart energy monitor for a home circuit. Non-invasive current transformer clamps measure real power on a circuit, and the device logs and displays it. Challenge: sampling and calibration, power factor calculation, safe isolation. Measure: accuracy against a reference meter. Note: keep all mains wiring inside certified equipment and use clamp-on sensors rather than breaking into live circuits.
Asset tracker with GNSS and cellular. A device reports location over LTE-M or NB-IoT and spends most of its time asleep. Challenge: power management, antenna placement, a backend dashboard. Measure: position accuracy, energy per report.
Secure OTA firmware update framework. Build a signed, fail-safe update system for a microcontroller fleet, with rollback. Challenge: bootloader design, cryptographic verification, testing failure cases such as power loss mid-update. Measure: recovery from injected failures, update time.
For smaller IoT builds that suit a single person, see our list of embedded systems and IoT project ideas.
Computer engineering: digital design, FPGAs and computer architecture
RISC-V soft-core processor on an FPGA. Implement a simple RV32I pipeline in Verilog or VHDL, run test programs and add a peripheral such as a UART. Challenge: pipeline hazards, verification. Measure: instructions per cycle on a benchmark, maximum clock frequency, FPGA resource use.
FPGA-accelerated image or signal processing. Offload a filter, FFT or edge detection from a CPU to FPGA logic. Challenge: fixed-point design, data movement, verification against a software model. Measure: speedup and power compared with a software implementation.
Hardware video game console or synthesizer. Generate VGA or HDMI video, or digital audio, directly from FPGA logic, with game or sound logic in hardware or on a soft-core. Challenge: precise timing, memory interfaces. Measure: frame rate, audio quality.
Custom logic analyzer. Capture digital signals at high speed with an FPGA or a fast microcontroller and stream them to a PC application. Challenge: buffering, triggering, the host software. Measure: maximum sample rate, channel count, trigger accuracy.
Robotics and control
Self-balancing robot. A two-wheeled robot balanced with an IMU and a control loop. Challenge: sensor fusion, controller tuning, motor drivers. Measure: disturbance rejection, recovery angle.
Autonomous mapping rover. A small rover that maps a room with lidar or ultrasonic sensors and navigates to a goal. Challenge: localization, path planning, integrating sensors on a mobile platform. Measure: map accuracy, success rate reaching goals.
Robotic arm with vision-guided pick-and-place. A camera identifies objects and an arm picks them up. Challenge: inverse kinematics, calibrating the camera to the arm, real-time control. Measure: pick success rate, cycle time.
Power and energy
Maximum power point tracking (MPPT) solar charge controller. A DC-DC converter that tracks a panel’s maximum power point and charges a battery. Challenge: converter design, the tracking algorithm, protection. Measure: conversion efficiency, tracking accuracy.
Battery management system for a lithium pack. Cell voltage monitoring, balancing and protection for a small low-voltage pack. Challenge: accurate measurement, state-of-charge estimation, safety logic. Measure: balancing performance, state-of-charge error.
Brushless DC motor controller. A three-phase inverter with field-oriented control. Challenge: power stage layout, current sensing, control firmware. Measure: efficiency, speed regulation.
Power projects carry real hazards. Work at low voltages where you can, follow your lab’s safety rules and get faculty sign-off before working with high voltage or large battery packs. For more EE-focused topics, see good senior project ideas for electrical engineering.
Signal processing and communications
Software-defined radio receiver application. Build a receiver for a specific signal (ADS-B aircraft broadcasts, weather satellite images or a sensor protocol) using an SDR front end. Challenge: demodulation, filtering, decoding. Measure: decode rate, sensitivity.
Acoustic direction finding. A microphone array estimates the direction of a sound source. Challenge: synchronized sampling, beamforming or time-difference-of-arrival algorithms. Measure: angular error.
Real-time audio effects processor. A DSP or microcontroller board that applies effects with low latency. Challenge: buffering, filter design, analog input and output stages. Measure: latency, noise floor, total harmonic distortion.
If a communications project involves transmitting, check the radio regulations that apply to you. Receive-only projects, and licence-free bands used within their limits, avoid most problems.
Biomedical and assistive technology
Wearable gait or fall detector. IMU-based detection of falls or gait changes, with alerts. Challenge: classification accuracy, power, false-alarm rate. Measure: sensitivity and specificity on recorded data.
Assistive navigation aid. An ultrasonic or time-of-flight sensor gives haptic feedback about obstacles. Challenge: sensor reliability, user interface design. Measure: detection range, response time.
Projects that touch human subjects or claim medical benefits may need ethics review at your institution, and they shouldn’t be described as medical devices. Frame them as prototypes or research demonstrators.
How to scope the project
Most senior design projects that fail do so because the scope was too big. A structure that helps:
- Write the requirements first. List perhaps five to ten measurable requirements, each with a test method.
- Define a minimum viable version. This is the smallest system that meets the core requirements, the one you’d still be proud to demo.
- List stretch goals separately. A mobile app, a second sensor type, a custom enclosure: add these only once the core works.
- Prototype the riskiest part early. If the whole project depends on a sensor being accurate enough, test that sensor in the first few weeks.
- Plan at least two PCB revisions if you’re designing boards. First revisions often have errors.
Splitting work across an ECE team
A mixed team of electrical and computer engineers can divide work along natural boundaries:
- Hardware: schematic, PCB layout, power supply, analog front ends.
- Firmware: drivers, control loops, RTOS tasks, communication.
- Software and backend: desktop or mobile app, data storage, visualization.
- Integration and testing: test plans, measurement rigs, documentation.
Agree on interfaces early: pin assignments, message formats, API endpoints. That way people can work in parallel. Weekly integration sessions catch mismatches before they pile up.
Practical risks to plan for
- Component availability. Check stock and lead times before committing to a specific chip, and choose parts with alternatives where you can.
- PCB fabrication and shipping time. Budget for turnaround and shipping, especially near holidays.
- Budget. Track spending from the start. Development boards, sensors and fabrication add up quickly.
- Regulated areas. Mains voltage, radio transmission and medical claims all bring extra rules. Ask your advisor early.
- Integration time. Leave several weeks at the end for integration and testing. It almost always takes longer than planned.
Finding more ideas
- Past project archives. Many universities publish senior project reports online. Cal Poly’s Digital Commons, for example, lists electrical engineering senior projects ranging from MPPT converters to antenna arrays and SDR beamforming. Reading past reports shows what’s achievable in a year.
- Industry sponsors. Sponsored projects come with a real customer and real requirements.
- Faculty research labs. A small piece of an ongoing research project can make a strong, well-supported capstone.
- Your own frustrations. Problems you’ve met in labs, jobs or hobbies often lead to the most motivated projects.
If you’d like to practise with smaller builds before senior design starts, our main list of embedded systems project ideas is organized by skill level.