Good senior project ideas for electrical engineering include a maximum power point tracking (MPPT) solar charge controller, a battery management system for a small lithium pack, a brushless DC motor controller, a precision energy or power-quality monitor, a custom antenna or antenna array with measured patterns, a software-defined radio receiver for a real signal, and a bicycle or exercise-machine power meter. What makes these good isn’t the topic itself. Each one requires you to analyse, design, simulate, build and then measure a circuit against a specification.
Below are more ideas, grouped by area, along with what turns each one from a hobby build into a senior-level project.
What makes an EE senior project “senior level”
A circuit copied from a magazine and soldered onto perfboard rarely meets a senior design rubric on its own. Advisors generally look for:
- Analysis and design work. Component values derived from requirements, not just copied.
- Simulation. SPICE, MATLAB/Simulink or similar tools used to predict behaviour before you build.
- A custom PCB. Particularly important for power and RF projects, where layout affects performance.
- Measured results against a specification. Efficiency curves, frequency response, noise figures, radiation patterns.
- A clear comparison between what you predicted and what you measured, with an explanation of the differences.
If an idea gives you room to do all five, it’s probably a good senior project.
Power electronics and energy ideas
MPPT solar charge controller. Design a buck or boost converter whose duty cycle is adjusted by a tracking algorithm (perturb-and-observe or incremental conductance) to extract maximum power from a panel. Measure converter efficiency across load and how closely the controller tracks the true maximum power point.
Bidirectional DC-DC converter. A converter that can move power in either direction between a battery and a DC bus, as used in energy storage and hybrid systems. The control and the mode transitions make it substantially harder than a one-way converter.
Battery management system (BMS). Monitor cell voltages, temperatures and current for a low-voltage lithium pack, with balancing and protection cut-offs. Estimate state of charge and compare it against coulomb counting or a reference.
Small-scale microgrid or DC house demonstrator. Combine a solar input, battery storage and loads on a low-voltage DC bus with a supervisory controller that manages energy flow. Some universities run long-term projects of this kind that teams contribute to year after year.
Wireless power transfer. A resonant inductive link that powers a small load across an air gap. Measure efficiency against distance and misalignment, and compare it with your coil and resonance calculations.
Solar-powered water pump controller. Drive a DC pump directly from a panel with MPPT and protection logic. It’s a practical system-level project with a clear end use.
Motor drives and electric vehicle ideas
Brushless DC (BLDC) motor controller. Build a three-phase inverter with either six-step commutation or field-oriented control, plus current sensing and protection. Measure efficiency and speed regulation under load.
Regenerative braking demonstrator. Show energy recovery from a spinning flywheel or a small vehicle back into a battery or supercapacitor, and quantify how much energy is recovered.
Electric vehicle charging interface (low-voltage demonstrator). Implement the signalling side of an EV charging protocol on a low-voltage test setup, without connecting to a real vehicle or the mains.
Stepper or servo drive with closed-loop control. Add an encoder to a stepper motor and implement closed-loop control to prevent missed steps. Compare its accuracy and torque behaviour with open-loop operation.
Analog, sensing and instrumentation ideas
Power-quality analyzer. Measure voltage and current waveforms safely (through isolated sensors), then compute RMS values, real and reactive power, power factor and harmonic content. Validate against a commercial meter.
Precision data acquisition front end. Design a low-noise amplifier and filter chain for a sensor such as a strain gauge, thermocouple or load cell, feeding a high-resolution ADC. Characterise the noise floor and linearity.
Bike or exercise-machine power meter. Use strain gauges or motor current measurements to estimate rider power output. Calibrating it against known loads is a substantial part of the work.
Impedance analyzer or LCR meter. Measure the impedance of components across frequency using a signal source and synchronous detection, and compare the results with a commercial instrument.
Low-cost oscilloscope or curve tracer. Design the analog front end, sampling and display for a basic measurement instrument. Bandwidth and input protection make this a real analog design exercise.
RF, antennas and communications ideas
Antenna design and characterisation. Design a patch, spiral or Yagi antenna, simulate it in an electromagnetic solver, build it and measure its return loss and radiation pattern. Projects like this are well represented in university senior project archives.
Software-defined radio (SDR) receiver. Use an SDR front end to receive and decode something real: aircraft ADS-B broadcasts, weather satellite images or low-power sensor transmissions. A related step up is digital beamforming with multiple receivers.
LoRa link budget and propagation study. Deploy LoRa nodes across a campus or rural area, predict range from a link-budget calculation, then measure received signal strength and packet loss, and explain the differences.
Visible-light or infrared communication link. Send data over modulated LED light, then design the transmitter, receiver and modulation scheme, and measure the bit error rate.
If your project transmits radio signals, make sure you stay within the rules for licence-free bands in your country, or get guidance from your department.
Control and robotics ideas with a strong EE component
Self-balancing robot with custom motor drivers. Designing your own H-bridge drivers and current sensing gives a balancing robot more EE depth than off-the-shelf modules would.
Magnetic levitation system. Levitate a small magnet or steel ball with an electromagnet, a position sensor and a feedback controller. It’s a classic, visually impressive control problem.
Vision-guided rover or tracking platform. Combine motor drives, sensors and an embedded processor. Keep the electrical design (power distribution, motor control) a central part of the scope.
For more embedded, FPGA and computer engineering topics, along with advice on writing requirements and splitting work in a team, see our guide to electrical and computer engineering senior design project ideas.
Safety considerations for EE projects
Electrical engineering projects can involve genuinely dangerous energy levels. General precautions:
- Prefer low-voltage designs. Many power electronics concepts can be demonstrated at low DC voltages instead of mains levels.
- Don’t work on mains or high-voltage circuits without supervision and your department’s approval. Follow your lab’s safety procedures.
- Treat lithium batteries with care. Use cells with protection circuits, avoid short circuits and charge with appropriate chargers in a safe location.
- Use isolation (isolated sensors, isolation transformers, isolated probes) whenever you measure mains-referenced signals.
- Add protection to your designs. Fuses, current limits and thermal shutdown belong in the design, not just the lab.
Your advisor and lab staff are the right people to ask about specific safety requirements. When in doubt, ask before you build.
How to pick between ideas
A quick checklist for comparing candidates:
- Can you write five or more measurable requirements for it?
- Does it include analysis and simulation as well as building?
- Can you prototype the riskiest part within the first month?
- Does each team member have a substantial piece to own?
- Can it be built safely and within budget?
An idea that passes all five is usually a sound choice. If you want something smaller to practise on first, our list of embedded systems project ideas includes beginner and intermediate builds.
Where to find real examples
Several universities publish their senior project reports online. Cal Poly’s Digital Commons, for example, lists electrical engineering senior projects covering MPPT trackers and DC/DC converters, solar-powered pumps, antenna arrays, SDR beamforming and LoRa propagation studies. Reading a few past reports from your own department, or from similar programs, is one of the best ways to calibrate how ambitious your project should be.